Big Stone Gap Classified Ad Listings

Freshly rebuilt, stock height linkpin/kingpin beetle or ghia spindles. I never have these on the shelf ready to go, but I can build them most anytime! If you've got all the parts and just need them assembled, I can do that too! Refinished spindle centers and carriers. Painted satin black. All new German/Febi king pins and bushings, reamed properly. link pin kit with new shims. New grease fittin...

2.5" Raised Balljoint type I spindles in Drum or Disc brake configuration. - Prototype set was jumped, abused and bashed by our test pilot for quite some time before I ever consideredbother set. - Will fit any Balljoint type I suspension car. 66-77. These are made using original cores, new 3/8" Thick plate off the waterjet and new snouts. That being said, these will widen your track width by 3/...

I've been doing metalwork on these cars for over 20 years now. Here I'm offering a full rotisserie chassis build up service, from a bare tunnel with fresh Wolfsburg West pan halves, all the way up to a turn key, add your body for a driver. *This ad is for restoration of YOUR chasiss. No chassis available outright * We have fixed some total piles of garbage in the past, so don't be afraid to sen...

We have loads of good, usable original VW parts and there's always various cars coming and going. I don't toss anything... We don't carry anything new, only good usable original parts. Mostly 58+ beetle. Little to no bus parts. Nothing exceptionally rare or early... I ship parts all over the globe as well. Message me with your needs! _________________ [email protected]

Now offering adjustable IRS springplates for your late type I or type III. *Single springplate only! You'll need to modify or swap out your four bolt plate covers to use these on a dual springplate car. * I typically need your stock set to build. I rarely have any on hand. These are not on the shelf, they're built to order * These plates are precision laser cut and have a notch incorporated int...

Baywindow bus passengers side footrests. Show your wife, husband, or significant mammal that you care about their footsies. DOM tube, laser cut tabs, built in a fixture so each one is the same as the last. I just installed mine with self tappers, but if you wanna do Nutserts and bolts that'll work too. Will send out raw. $100 picked up or $125 shipped anywhere in the continental US Please keep ...

Now offering offset springplates for your 55-67 bus. These allow direct bolt in of a 68 beetle transaxle or any type III swingaxle trans. No modification to your bus required! Swap the bus nose cone and hockeystick over and it'll bolt right in. These eliminate the reduction boxes and provide a 3.5" or more reduction in ride height, depending on where you set your torsion bars. Pricing is with y...

**NEW ,Adjustable Narrowed Type II Bus Beams, 55-79 ** Type II 55-67 Linkpin beams - 68-79 Balljoint beams and 68-79 linkpin conversions! See the full details and order here: http://valleyautowerks-com.3dcartstores.com/_p_15.html Built here, in my shop, on my table, by me! Available 2,3,4 & 5" Narrowed. Brand new steel tubing, cnc'd cut parts, top notch materials, all jig built! Linkpin or Ball...

Lowered swing axle, beyond one spline? You need to correct your toe in issues! See details and order here: http://valleyautowerks-com.3dcartstores.com/_p_16.html I've been running extended/notched stock plates for ages now, tried and true way of extremely reducing bump steer, tire wear, ride quality and overall driving experience! Even on an extremely cambered car, you can triple your tire life...

- - -100% NEW Narrowed Adjustable Balljoint Type I Beams - - - - Narrowed 2"- 8"depending on your needs Built here, in my shop, on my table, by me, since 2004! See full details and order here: http://valleyautowerks-com.3dcartstores.com/_p_18.html These beams are 100% NEW metal and DOM tubing. Completely jig built and test fitted before shipment, to avoid headaches on your end! No body modifica...

I build full Type I setups adapted to fit into your Type III, but I also offer just the mounts you need to weld onto a stock or custom Type I Beam to fit into your Type III if you're feeling crafty. Do you like puzzles? Wanna build/adapt a type I beam into your type III? Have I got a treat for you. *This is for a set of mounts only. You or someone else must weld these onto a type I beam. Fabric...

Flipped/ dropped spindle service for your 55-67 bus. Send me your stock spindles, I disassemble and inspect them, clean/blast the components, modify them and re assemble them as 3.5" dropped spindles! I always take them apart, and send photos of the condition of your spindles before we proceed. You will need both tie rods to be adjustable. I also usually take 1/2" or so off of each one, for pro...

Have a narrowed beam, but no tie rods? Want some new Tie Rods to match, done the right way? Email me! These are brand new DOM steel tubes, cut to the length you need and tapped. LH and RH like they should be. Not cut up junk! I can make them for type I, II or III! Let me know the year of your car and what Size beam or the lengths you need. Price is for a PAIR of tie rod tubes, tapped RH and LH....

Refinished original Balljoint front trailing arms ( 66+ type I ) Fully turn key, original German arms with balljoints installed, eccentric camber nuts and grubs screws too, if needed. See details and order here: https://valleyautowerks-com.3dcartstores.com/_p_25.html * Please contact me before hand to be sure I have cores available if you're not sending a set in* as follows: Set of four origina...

Rear IRS trailing arms, narrowed 1" per side, to accept type3 Automatic LEFT axle or empi axle #90-6907. Fit some bigger tires, better wheels or more offset! *This is not an outright set of arms for sale. This is a service in which I modify the CLEAN arms you send me and return them. I never have these on the shelf available.* Built here, in my shop, on my table, by me! Sent out raw, no hidden ...

Hand made one of these for my personal car and had some interest in them, so I made a template and now get them laser cut. It's saved my apron from total annihilation on more than one occasion. These fit any type I, BJ or LP. Only hangs down 3/16" and will help you skip over obstacles, landmines, roadkill, curbs, jumps, bumps and lumps! See full details and order here: http://valleyautowerks-co...

Now offering fresh Disc or Drum, Linkpin dropped spindles, built and ready to ride! **These fit your pre-66 Type I.** If you've got all the parts but just need the bushings pressed, reamed and assembled, I can do that too! $425 with your sent in stock core spindles, or $600 outright with no cores! *If I have core spindle carriers available. Please contact me first to see. See details and order ...

Brand new steel, Scratchbuilt Narrowed Linkpin Type II airride beam. I Make these in Balljoint too if you need! Built here, in my shop, on my table, by me! ** I do NOT sell the torsion keys and mounts separately ** See the full details and order here: http://valleyautowerks-com.3dcartstores.com/_p_26.html **These are built to order, I have nothing in stock and ready to go. Please email me for c...

Linkpin type I based, Type III Airbeam / Air ride / Front Bag setups. This is a type I based beam, that bolts directly into your 62-74 Type III, Notchback, fastback or squareback. Available 2-5" narrowed. Available with shocktowers on up to 3" beams. This is a type I based beam, with mounts to bolt directly into your type III pan. Completely jig built, like all my other suspension parts. Fully ...

- - -100% NEW Narrowed Adjustable Linkpin Type I Beams - - - - Narrowed 2"- 8"depending on your needs Built here, in my shop, on my table, by me! Now featuring my in house produced beam bushings, 100% made in the USA! See details and order here: http://valleyautowerks-com.3dcartstores.com/_p_14.html These beams are 100% NEW metal and DOM tubing. Completely jig built and test fitted before shipm...